Polymer Stabilized Geoinjection (PSGi®)

Different injection materials are suitable for the stabilisation of dry and moist gravel and sand bases and hence to create ground stabilisation.

The injection procedure is accomplished with packers or injection lances directly into the areas to be strengthened and hardened. The hardened resin/sand mixtures are distinguished by their high rigidity and stability.

  • Penetrates even into fine sandy soils
  • Adjustable to soil conditions
  • Solidifying and sealing effect in one operation
  • Worldwide references available

Recommended systems

Acrylate gel

RUBBERTITE®

Rubber-elastic, 3 C acrylate gel, multi purpose applicable

  • Very low viscous
  • Very good penetration
  • Proven stability of at least 20 years

ECOCRYL

Adjustable, low viscous, quickly reacting 3 C acrylate gell

  • quickly reacting

SOLIDCRYL

Adjustable, low viscous rigid acrylate resin with high final strength. Specially to create ground stabilisation

  • Low viscous
  • Very good penetration
  • High final strength

Polyurethane resin

PUR-O-STOP

1-component injection resin based on polyurethane

  • Filling of small voids (<300 litres)
  • Consolidation of soil / open rock formation

PUR-O-STOP FS

Very quickly reacting, from ridged to tough elastic, 2K polyurethane resin, which foams up in contact with water

  • Filling of small voids (<300 litres)
  • Consolidation of soil / open rock formation

PUR-O-STOP FS-L

Slowly curing, from ridged to tough elastic, 2K polyurethane resin, which foams up in contact with water

  • Filling of small voids (<300 litres)
  • Consolidation of soil / open rock formation

PUR-O-STOP HF

Foaming, quick reacting, 2K Polyurethane based resin

  • Filling of small voids (<300 litres)
  • Consolidation of soil / open rock formation

Silicate resin

FOAM SEAL PLUS

Fast-reacting, slightly flexibilized, strongly expanding injection foam based on silicate resin, contains flame retardants

  • filling of cavities in mining, civil engineering and tunnel construction
  • consolidating rock
  • stopping of water infiltration
  • self-compacting due to high foam factor

SOLID SEAL

Non-foaming, ridged to tough elastic injection resin based on silicate

  • Underpinning of massive structural elements
  • for friction-fit filling of cracks
  • displaces water without foaming

SOLID SEAL SL

Non-foaming, ridged to tough elastic injection resin based on silicate

  • low viscosity
  • high fluidity
  • displaces water without foaming
  • Underpinning of massive structural elements

SOLID SEAL TX

Thixotropic, very fast reacting silicate resin

  • thixotropic (no flowing away, processing also overhead)
  • very good adhesive properties
  • particularly rapid strength development
  • no mixing with water

TRACKFIX SIL

Especially for stabilization of track gravel

  • Universally applicable in railway constructions, regardless of type and moisture of gravel
  • Approved by the German Railway Authorityl

Injection cement

F8000

Single-component injection material based on extra-fine cement

  • For soil stabilization and sealing

Use

By reason of its extremely low viscosity and its high mechanical stability in hardened condition RUBBERTITE® is very suitable for the compression and stabilisation of ground. A penetration of the ground is usually achieved via injection lances in this procedure. The hardened gel/sand mixture is distinguished by a high degree of rigidity and stability.

In the new construction of tunnels which are erected in tubbing sections or pipe drive, RUBBERTITE® is employed for the stabilisation of the ambient ground area in the new construction of tunnels. This is essential especially if repair work on the road heading machinery must be carried out or when leakage must be remedied in the region of the start and target shafts.

Ground stabilization – Gas Pipeline in Nature Conservation Area

Ground stabilization, Railway station, Königslutter

Ground stabilization JadeWeserPort, Wilhelmshaven