Injection hoses

Injection is a proven method of sealing against pressurised water in structural renovations. The grouting of injection hoses also provides the benefit of using the advantages of injection technology in new construction specifically for the sealing of construction joints.
MEDIPRESS and VPRESS® injection hoses, which can be injected several times, have been used successfully for construction joint sealing for many years. They can be injected with microfine cement, polyurethane resin or acrylate gel.
In contrast to passive sealing systems such as conventional water stops and waterstop sheets, which only seal off due to the so-called circumference extension, active systems such as injection hoses and injection grouts can be used to cancel out possible weak points in the concrete caused by cracks or badly compacted concrete.

  • Sealing and restoration in one step
  • Single injection with Polyurethane resin
  • Multiple injection with microfine cement  or acrylate gel
  • Specially suitable for difficult construction joint run

Recommended systems

VPRESS®

Injection hose consisting of a slightly-foamed PVC with ribbed surface

Also with 10 mm inner-Ø for special requirements and overlength up to 30 m
Good locking into concrete

ECOPRESS

Injection hose consisting of a slightly-foamed PVC with ribbed surface

  • Good locking into concrete
  • Overlenght approved up to 20 m

Recommended grout

RUBBERTITE®

Rubber-elastic, 3 C acrylate gel, multi purpose applicable

  • Very low viscous acrylate gel with high flexibility
  • Very good penetration, even in water filled cracks
  • Long term stable. Proven stability of at least 16 years

PUR-O-CRACK

2-component injection resin based on polyurethane

  • Officially approved system
  • Proven against water pressure of 7 bars
  • Approved for use in CHF and LMSS plants

PUR-O-RIP

2-component high flexible injection resin based on polyurethane

  • Universal and economical
  • highly flexible < -50°C

PUR-O-RIP LV

Low-viscous, 2-component injection resin based on polyurethane

  • Very low viscous
  • for hairline cracks

PUR-O-RIP PLUS

2-component resin based on Polyurethane, which foams up in contact with water

  • Slightly foamy

F8000

Single-component injection material based on extra-fine cement

  • For injection in cracks above 0.2 mm

F9200

Ready to use dry mixture based on cement, non shrinking.

  • For injection in cracks above 0.375 mm
  • Non shrinking
  • for VPRESS® injection hose with 10mm inner-Ø

F9300

Injection and anchor mortar

  • does not shrink
  • is easy to process
  • frost protected

Equipment

Packer for injection hoses

For screw-in the bleeding air hose

Stopper Inner thread M 8

7mm free passage, for cement injection.


Fast click stopper R1/2″

ball valve R1/2″,
Geka-coupling

hose for bleeding air from injection hoses

screw-in connection

Protective box

shutter-plug

for closing airbleed hoses

  • for hose inner ø 6 mm
  • for hose inner ø 10 mm

Shutter connectors and cover caps

Extension pipe

M 8, Length 35mm, for shutter connectors for cement injection

Plastic clips

for fixing

Metal clips

for fixing

Punsh dowel for metal clamp

with hole diameter of 6,1 mm

Fixing clamp

for fixing injection hoses on metal water stops.

Clamp

to fix injectionhoses like MEDIPRESS, VPRESS and ECOPRESS to PVC water stops

Use

Processing

The hoses are fitted in the center of the reinforcement using hose sections of between 8 and 10 m in length. Longer lengths of hose can be achieved, if required due to construction conditions, depending on the grout used.
MEDIPRESS, VPRESS® or ECOPRESS injection hoses and air bleed hoses are joined simply and without tools using screw-in grommets which are screwed into the hoses by hand.
Fixing of the injection hoses is carried out using plastic clips (which can be dowelled or pressed into fresh concrete) or with nail clips. As a rule the venting ends are guided from the construction at right angles. For multiple injection of the injection hoses it is recommendeded either to fit the venting ends with nail packers or to keep them together in storage boxes.

Storage box and nail packers

Nail packers are directly plugged into the venting hose and onto the shell partition. The coloured foam sponges must match the colour of the hose so that the corresponding section of the hose can be identified after the casting of the concrete.

Injection hoses for sealing of biogas plants

Flexible sealing system, approved for use in CHF and LMSS plants